Send Message
Home
Products
About Us
Factory Tour
Quality Control
Contact Us
Request A Quote
News
Shijiazhuang Hanjiu Technology Co.,Ltd
Home News

The installation and use of full hydraulic steering note

China Shijiazhuang Hanjiu Technology Co.,Ltd certification
China Shijiazhuang Hanjiu Technology Co.,Ltd certification
Hello, Hanhan, my dear friend! Keep in touch with you by whatsapp.

—— Ricky Naidoo

Hello, Dear Alysa, you looks like a tall and lovely girl. Thank you for your catalogues, I will reply you soon.

—— Bhavin Gandhi

Dear Emily, you are a sweet girl. Keep in touch.

—— Roy Quemada

Dear Shirley, thank you for your patient. I will be back soon.

—— Sam

Dear Simon, sample is received. I will detect it asap.

—— JACK LORSHBOUGH

Dear Albert, good job, we can be good partner.

—— larry timmons

I'm Online Chat Now
Company News
The installation and use of full hydraulic steering note
Latest company news about The installation and use of full hydraulic steering note

The installation and use of full hydraulic steering note


1, installation precautions:
(1) When installation steering gear must ensure coaxiality with column, must have a gap of 1 mm in the axial direction.
(2) The depth of screw connection to the steering column tightening steering column is ≤15mm.
(3) After steering gear installed, must check steering wheel turns to ensure the flexibility of the return position.
(4) Connection pipeline: P oil port connects to the oil supply pump, T oil port connects to the oil tank, and A and B oil ports
respectively connect the left and right oil chambers of the steering gear.

 

2, oil flow rate considerations:
(1) The oil supply circuit connected to the P oil port, the oil flow rate in the pipe is recommended to be ≤1.5m/s.
(2) The pressure circuit of the oil cylinder connected to the A and B ports is recommended. The oil flow rate in the pipe is
recommended to be ≤4~5m/s.


3, other matters needing attention:
(1) The diameter of the steering wheel must not exceed 500mm.
(2) A return filter with a filter accuracy of 30 μm should be installed in the return line of the steering gear. The position of tank is
generally higher than installation position of steering gear, and return pipe is inserted below oil level, so oil can be filled only when
the manpower is turned, and air can be prevented from entering the oil line.
(3) The oil viscosity of steering gear is 17cst~33cst. It is recommended to use low-condensation hydraulic oil. Steering gear
allows normal working oil temperature 20°C to 80°C, and the limit working oil temperature range is -30°C to 100°C. Reminder: In
case of abnormal oil temperature, steering performance will decrease.
(4) After steering system assembled, it shall be tested: clean oil tank before operation, inject hydraulic oil to the max oil level.Loosen
cylinder nipple and allow pump to run at low speed until it is out of oil. Remove link,turn the steering wheel so that the piston
reaches left or right position, and then fill the tank to specified level. Tighten all thread connections, connect the piston rod, and
check if the steering system is working properly.
(5) It must be ensured that the oil is clean to prevent the dirt to cause steering failure. Always check the condition of the filter
element and the oil. If necessary, give a replacement.
(6) If steering failure, must be carefully check the reason first. The steering wheel must not be pulled hard, and the steering gear
should not be disassembled to avoid damage to parts. It is forbidden for two people to turn the steering wheel at the same time.

 

 

latest company news about The installation and use of full hydraulic steering note  0

 

 

Pub Time : 2019-04-27 10:39:44 >> News list
Contact Details
Shijiazhuang Hanjiu Technology Co.,Ltd

Tel: 86-311-68123061

Fax: 86-010-80115555-568844

Send your inquiry directly to us (0 / 3000)